Make your next PCB ready for production

A manufacturing partner for the next board revision

Eurocircuits serves electronics designers who need bare boards or assembled prototypes while keeping fabrication, component procurement and assembly preparation connected. Its own European facilities sit behind an online workflow for pricing, data review and ordering.

The wider portfolio includes PCB proto, DEFINED IMPEDANCE pool, RF pool, IMS pool, SEMI-FLEX pool and solder-paste stencils, alongside component sourcing and Parts Pre-Order. Our shortlist focuses on the decisions many electronica engineering and NPI teams face: a conventional board, a layout constrained by a fine-pitch package, and the path to an assembled unit. The Visualizer is the common preparation layer across those services.

Who should make time for Eurocircuits?

Prioritise this conversation if your next milestone depends on turning design files into a manufacturable PCB or PCBA, particularly when the team is still refining the layout or BOM.

For special build-ups or requirements outside the configurator, send the design for engineering evaluation before treating an online price as an accepted production specification.

Three routes from layout to hardware

These are established Eurocircuits offerings to discuss at electronica. Choose the manufacturing route around the design constraints, then decide whether to add assembly.

STANDARD pool

STANDARD pool is the broad FR-4 fabrication route for conventional prototype and small-series boards, supplied as single circuits or panels and available with assembly. Its configurator distinguishes panel-sharing options from a dedicated non-pooling production panel, so a change in build-up or processing option can change the commercial route. Upload the PCB data to review parameters and reported manufacturing issues, then compare the quantity and delivery matrix. For an embedded controller revision, a useful evaluation is to see which layout or finish choices remain poolable and which require a separate panel, leaving the team with a clear specification and quotation basis.

HDI pool

HDI pool addresses layouts where a fine-pitch package needs microvias and compact fan-out while much of the PCB can use conventional technology. The service uses predefined FR-4 build-ups and distinguishes poolable from non-poolable parameters. The design guidance supports staggered microvias rather than stacked vias, so component pad geometry and the available layer transitions matter early. For a compact controller using a BGA, review the package footprint and escape routing against a candidate build-up; the useful outcome is a feasible routing approach and a list of constraints to take back into CAD. Routability alone does not establish signal integrity, EMC or thermal suitability.

PCB Assembly

PCB Assembly turns Eurocircuits-manufactured bare boards into assembled prototypes or small series using single- or double-sided SMT, through-hole or mixed technology. Upload the PCB design together with the bill of materials and component placement list; the Visualizer exposes reported assembly issues before ordering. Eurocircuits sources components, while parts it cannot source can be supplied by the customer. For a sensor interface board, follow a polarised component from its BOM identity to footprint and placement, then review any procurement issue. The outcome should be an agreed component and assembly data set, with inspection coverage and the remaining product-level validation responsibilities understood.

What changes the sourcing decision

The useful signals are the details that change layout choices, supplier scope or the handover to production.

• Panel-sharing options
• European production
• BOM-led preparation

We would prioritise a design-specific walkthrough over a general presentation: it exposes whether the manufacturing rules, component route and review workflow fit the way your team releases hardware.

Belgian base, European production

Eurocircuits N.V. is headquartered at Antwerpsesteenweg 66, 2800 Mechelen, Belgium. The group specialises in PCB prototypes and small-series manufacturing and assembly, with production operations in Germany and Hungary and regional sales and customer support. Its portfolio spans conventional FR-4, HDI, defined-impedance, RF, insulated-metal-substrate and flex-to-install boards, as well as stencils and assembly services. Free online manufacturing tools and technical guidance support that manufacturing business.

Build a two-stage visit around your project

Published visitor exhibition hours are 09:00–18:00 on 10–12 November and 09:00–15:00 on 13 November, Munich local time. The sequence below is TSI editorial advice, not a booked appointment.

Choose a day that fits your itinerary and arrange a discussion directly with Eurocircuits if a particular specialist is needed.

Five questions that turn a visit into a decision

Use your actual board and component data to make the answers actionable.

1. For STANDARD pool, which options in this board move it from pooling to non-pooling?

   Establish the fabrication cost drivers and whether a specification change is acceptable before comparing quotes.

2. For HDI pool, can this BGA fan-out fit the available build-up using staggered microvias?

   Decide whether the package and routing strategy fit the service before investing in a complete layout.

3. For PCB Assembly, how will you resolve a BOM part whose footprint or placement data does not match?

   Agree the correction and approval responsibility so procurement and assembly use the same released revision.

4. For PCB Assembly, which parts can you source, and which should we supply or place through Parts Pre-Order?

   Identify purchasing responsibilities and component risks before fixing a delivery expectation.

5. For our assembled board, what inspection evidence is supplied and what functional testing remains with us?

   Define the acceptance package and budget for the product validation that manufacturing checks do not cover.

Find Eurocircuits at electronica 2026

Send a project brief before the show

Contact Eurocircuits at euro@eurocircuits.com or +32 15 28 16 30. Mention electronica 2026 and send your application, target quantity, desired delivery and key manufacturing question. For a technical review, prepare PCB data, a BOM and component placement list, plus any critical package datasheets; agree how to share confidential files with the team.

Before you go